Keine SMART-Infos an 3Ware Controller

C

cmer

New Member
Moin,

weiss jemand von Euch woran es liegen könnte, dass ich durch das 3DM 2 Utility von 3Ware keine SMART Informationen aus den angeschlossenen Platten auslesen kann (zumindest im Klartext)?

Liegt das evtl. daran, dass die Platten über eine Backplane (Chenbro) am 3Ware Controller hängen?

Extra Drive Info (Controller ID 0 - Port 0)

Drive Type SATA
Serial # 9QMxxxxx
Firmware SN04
Reallocated Sectors 0
Power On Hour 0
Temperature 0°C (0°F)
Spindle Speed 0 RPM
Queuing Supported Yes
Queuing Enabled Yes
Link Supported 1.5 Gbps, 3.0 Gbps
Link Enabled 3.0 Gbps
Click to expand...

Controller Details (Controller ID 0)
Model 9650SE-4LPML
Serial # L326002Axxxxxxx
Firmware FE9X 3.08.00.016
Driver 3.00.04.020
BIOS BE9X 3.08.00.004
Boot Loader BL9X 3.08.00.001
Available Memory 224 MB
Bus Type PCIe
Bus Width 4 lanes
Bus Speed 2.5 Gbps/lane
# of Ports 4
# of Drives 4
# of Units 1
Click to expand...

Das S.M.A.R.T. Datenfeld in HEX wird allerdings angezeigt:

S.M.A.R.T. (Controller ID 0 - Port 0)

0A 00 01 0F 00 77 63 66 BD F9 0C 00 00 00 03 03
00 5F 5E 00 00 00 00 00 00 00 04 32 00 64 64 15
00 00 00 00 00 00 05 33 00 64 64 00 00 00 00 00
00 00 07 0F 00 3F 3C 8B 0C 1C 00 00 00 00 09 32
00 64 64 C5 01 00 00 00 00 00 0A 13 00 64 64 00
00 00 00 00 00 00 0C 32 00 64 64 15 00 00 00 00
00 00 B8 32 00 64 64 00 00 00 00 00 00 00 BB 32
00 64 64 00 00 00 00 00 00 00 BC 32 00 64 64 01
00 00 00 00 00 00 BD 3A 00 64 64 00 00 00 00 00
00 00 BE 22 00 46 37 1E 00 1A 27 00 00 00 C2 22
00 1E 2D 1E 00 00 00 10 00 00 C3 1A 00 29 22 66
BD F9 0C 00 00 00 C5 12 00 64 64 00 00 00 00 00
00 00 C6 10 00 64 64 00 00 00 00 00 00 00 C7 3E
00 C8 C8 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 82 00 71 02 00 7B
03 00 01 00 01 78 02 00 00 00 00 00 00 00 00 00
00 00 00 00 D6 02 00 00 05 06 06 06 05 06 06 06
06 00 00 00 00 00 00 00 00 01 01 00 00 00 00 00
00 00 00 00 00 00 00 00 EF 96 80 B7 7B 01 00 00
00 00 00 00 01 00 28 00 52 32 E7 1B BF 0D 00 00
41 4B 12 2A 00 00 00 00 00 00 00 00 85 38 7A 04
00 00 00 00 00 00 00 00 8E 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 A8
Click to expand...

Irgendjemand eine Idee, was man da machen kann?

Grüsse,
cmer
 
Hallo,

ich habe einen 3Ware-Controller mit 2 S-ATA Anschlüßen, und lese die Smartdaten de Festplatten mit folgendem Befehl aus.

Code: 
smartctl -d 3ware,[B]0[/B] -a /dev/twe0
Der Fett gedruckte Buchstabe 0 ist bei mir A und die 1 ist bei mir B
Also wär bei dir C .. 2


Einfach mal ausführen, da werden dir paar Infos über die einzelnen Platten gegeben.
Falls du Fragen hast, melde dich.
 
You must log in or register to reply here.
Back
Top